nichia sts-da1-2675a nichia corporation specifications for white led NSBWL066A built-in esd protection device rohs compliant
nichia sts-da1-2675a 1 specifications (1) absolute maximum ratings item symbol absolute maximum rating unit forward current i f 600 ma pulse forward current i fp 900 ma allowable reverse current i r 85 ma power dissipation p d 21.6 w operating temperature t opr -40~100 c storage temperature t stg -40~100 c junction temperature t j 130 c * absolute maximum ratings at t c =25c. * i fp conditions with pulse width 10ms and duty cycle 10%. * the operating temperature (t opr ) range is the range of case temperatures. (2) initial electrical/optical characteristics item symbol condition typ max unit forward voltage v f i f =320ma 33.3 - v luminous flux v i f =320ma 1520 - lm rnn color rendering index r a i f =320ma - - - luminous flux v i f =320ma 1490 - lm r70 color rendering index r a i f =320ma 73 - - luminous flux v i f =320ma 1370 - lm r8000 color rendering index r a i f =320ma 83 - - x - i f =320ma 0.3447 - - chromaticity coordinate y - i f =320ma 0.3553 - - thermal resistance r jc - 1.8 2.1 c/w * characteristics at t c =25c. * luminous flux value as per cie 127:2007 standard. * chromaticity coordinates as per cie 1931 chromaticity chart. * r jc is thermal resistance from junction to t c measuring point.
nichia sts-da1-2675a 2 ranks item rank min max unit forward voltage - 30 36 v j1450 1450 1600 j1300 1300 1450 luminous flux j1150 1150 1300 lm rnn r a - - - r70 r a 70 - - r a 80 - - color rendering index r8000 r 9 0 - - color rank rank sm503 x 0.3447 center point y 0.3553 * ranking at t c =25c. * forward voltage tolerance: 0.32v * luminous flux tolerance: 7% * color rendering index r a toleranc e: 2 * color rendering index r 9 toleranc e: 6 .5 * the r 9 value for the above rank shall be greater than 0. * chromaticity coordinate tolerance: 0.005 * the color rank has a chromaticity range within a 3-step macadam ellipse. * leds from the above ranks will be shipped. the rank combination ratio per sh ipment will be decided by nichia. luminous flux ranks by color ra nk, color rendering index rank ranking by luminous flux ranking by color coordinates, color rendering index j1150 j1300 j1450 rnn,r70 sm503 r8000
nichia sts-da1-2675a 3 chromaticity diagram 0.20 0.25 0.30 0.35 0.40 0.45 0.20 0.25 0.30 0.35 0.40 0.45 x y sm503
nichia sts-da1-2675a 4 outline dimensions sts-da7-3990 nsbxl066a ? no. ( g unit: mm) this product complies with rohs directive. u? rohs ?m??? * ( g unit: mm, tolerance: 0.3) k o protection device a 1 2max the center of emitting area to be centered 0.3mm. k??t 0.3mm (11) 7 14 19 14 17 16 cathode anode (9) ? item ??`| package materials ??| encapsulating resin materials ?O| electrodes materials | weight description ?? ceramics ?`? ? + w? silicone resin (with diffuser and phosphor) ? au-plated 1.2g(typ)
nichia sts-da1-2675a 5 soldering ? recommended hand soldering condition temperature 380c max soldering time 5sec max * hand soldering must not be performed more than once. * since the silicone used in the encapsulating resin frame is soft, do not press on the encapsulating resin frame or resin are a. pressure can cause nicks, chip-outs, encapsulant delaminati on and deformation, and wire br eaks, decreasing reliability. * repairing should not be done after the leds have been soldered. it should be confirmed beforehand whether the characteristics of the leds wi ll or will not be damaged by repairing. * when soldering, do not apply stre ss to the led while the led is hot. * when using a pick and place machine, choose an appropriat e nozzle for this product. using a pick-and-place nozzle with a smaller diameter than the size of the led's em itting surface will cause damage to the emitting surface and may also cause the led not to illuminate. * when flux is used, it should be a ha logen free flux. ensure that the manufacturing process is not designed in a manner where the flux will come in contact with the leds.
nichia sts-da1-2675a 6 tray dimensions 1 ???? 54 ? * ( g unit: mm) tray size: 54pcs sts-da7-3991 nxxxl066x ? no. all dimensions shown are for refere nce only and are not guaranteed. ?? * 16.7 7 19.7 210 297 27 135 28 224
nichia sts-da1-2675a 7 packaging - tray pack nichia led sts-da7-0007c nxxxxxxx ?` seal ?? tray ? label ? label rohs nxxxxxxx xxxx led ******* nichia corporation 491 oka, kaminaka, anan, tokushima, japan type lot qty. ymxxxx-rrr pcs rohs nxxxxxxx xxxx led ******* rrr pcs type rank qty. nichia corporation 491 oka, kaminaka, anan, tokushima, japan ? no. ????????????`???? trays are shipped with desiccants in heat-sealed moisture-proof bags. ? desiccants ??K???`? moisture-proof bags are packed in cardboard boxes with corrugated partitions. ?? moisture-proof bag if not provided, it will not be indicated on the label. ******* is the customer part number. O??????? * ******* ?? ? for details, see "lot numbering code" in this document. * ??????????? * u???????n?go??`y? ?`???????y?????? * ??\H?y?B???y? * ?QH??n?????u?p?????? * products shipped on trays are packed in a moisture-proof bag. they are shipped in cardboard boxes to protect th em from external forces during transportation. using the original package material or equivalent in transit is recommended. do not expose to water. the box is not water-resistant. do not drop or expose the box to external forces as it may damage the products.
nichia sts-da1-2675a 8 lot numbering code lot number is presented by using the following alphanumeric code. ymxxxx - rrr y - year year y 2009 9 2010 a 2011 b 2012 c 2013 d 2014 e m - month month m month m 1 1 7 7 2 2 8 8 3 3 9 9 4 4 10 a 5 5 11 b 6 6 12 c xxxx-nichia's product number rrr-ranking by color coordinates, ranking by luminous flux, ranking by color rendering index
nichia sts-da1-2675a 9 derating characteristics nsbxl 066a sts-da7-4280 ? no. derating1 0 200 400 600 800 1000 0 20406080100120 (86, 600) (100, 412) duty 10 100 1000 110100 60 0 90 0 S a ll owa bl e forwar d c urr ent ( ma ) `??y?-S temperat ure at measure point on a case v s allowable forward current S allowable forward current(ma) `??y? temperature at measure point on a case(c) ?` ?` duty ratio(%) ?`?`-S duty ratio vs allowable forward current t a = 25c
nichia sts-da1-2675a 10 optical characteristics NSBWL066A ? no. sts-da7-4314 spectrum 0.0 0.2 0.4 0.6 0.8 1.0 350 400 450 500 550 600 650 700 750 ? relative illuminance(a.u.) directivity1 90 80 70 60 50 40 30 20 10 0 -10 -2 0 -30 -4 0 -50 -60 -70 -80 -9 0 k??? spectrum k? relative emission intensity(a.u.) L wavelength(nm) ? directivity ? radiation angle 10.500.51 * ??? all characteristics shown are for reference only and are not guaranteed. 320ma i fp = t a =25c 320ma i fp = t a =25c * ??? rnn ???? the graphs above show the characteristics for rnn leds of this product.
nichia sts-da1-2675a 11 optical characteristics NSBWL066A ? no. sts-da7-4315 spectrum 0.0 0.2 0.4 0.6 0.8 1.0 350 400 450 500 550 600 650 700 750 ? relative illuminance(a.u.) directivity1 90 80 70 60 50 40 30 20 10 0 -10 -2 0 -30 -4 0 -50 -60 -70 -80 -9 0 k??? spectrum k? relative emission intensity(a.u.) L wavelength(nm) ? directivity ? radiation angle 10.500.51 * ??? all characteristics shown are for reference only and are not guaranteed. 320ma i fp = t a =25c 320ma i fp = t a =25c * ??? r70 ???? the graphs above show the characteristics for r70 leds of this product.
nichia sts-da1-2675a 12 optical characteristics NSBWL066A ? no. sts-da7-4316 spectrum 0.0 0.2 0.4 0.6 0.8 1.0 350 400 450 500 550 600 650 700 750 ? relative illuminance(a.u.) directivity1 90 80 70 60 50 40 30 20 10 0 -10 -2 0 -30 -4 0 -50 -60 -70 -80 -9 0 k??? spectrum k? relative emission intensity(a.u.) L wavelength(nm) ? directivity ? radiation angle 10.500.51 * ??? all characteristics shown are for reference only and are not guaranteed. 320ma i fp = t a =25c 320ma i fp = t a =25c * ??? r8000 ???? the graphs above show the characteristics for r8000 leds of this product.
nichia sts-da1-2675a 13 forward current characteristics / temperature characteristics NSBWL066A sts-da7-4317 ? no. tavf 20 25 30 35 40 45 -60 -40 -20 0 20 40 60 80 100 120 ta iv 0.6 0.8 1.0 1.2 1.4 -60 -40 -20 0 20 40 60 80 100 120 vfif 10 100 1000 20 25 30 35 40 45 320 900 relative luminous flux(a.u.) ??- ambient temperature vs relative luminous flux for ward curren t( ma) ifiv 0.0 0.5 1.0 1.5 2.0 2.5 3.0 0 200 400 600 800 1000 relative luminous flux(a.u.) - forward current vs relative luminous flux forward current(ma) ?R- forward voltage vs forward current ??-?R ambient temperature vs forward voltage ?R forward volta g e ( v ) ?R forward voltage(v) ?? ambient temperature( c) ?? ambi ent t em p erature ( c ) t a =25c * ??? all characteri st ics show n are for reference only an d are not guaranteed. t a =25c i fp = 320ma i fp = 320ma
nichia sts-da1-2675a 14 forward current characteristics / temperature characteristics ? no. NSBWL066A sts-da7-4318 taxy 0.33 0.34 0.35 0.36 0.37 0.32 0.33 0.34 0.35 0.36 -40c 25c 100c x ifxy 0.33 0.34 0.35 0.36 0.37 0.32 0.33 0.34 0.35 0.36 20ma 100ma 320ma 600m a 900ma x y y 320ma i fp = ??-? ambient temperature vs chromaticity coordinate -? forward current vs chromaticity coordinate t a =25c * ??? all characteristics shown are for reference only and are not guaranteed. * ??? rnn ???? the graphs above show the characteristics for rnn leds of this product.
nichia sts-da1-2675a 15 forward current characteristics / temperature characteristics ? no. NSBWL066A sts-da7-4319 taxy 0.33 0.34 0.35 0.36 0.37 0.32 0.33 0.34 0.35 0.36 -40 c 25 c 100 c x ifxy 0.33 0.34 0.35 0.36 0.37 0.32 0.33 0.34 0.35 0.36 20m a 100ma 320ma 600ma 900m a x y y 320ma i fp = ??-? ambient temperature vs chromaticity coordinate -? forward current vs chromaticity coordinate t a =25c * ??? all characteristics shown are for reference only and are not guaranteed. * ??? r70 ???? the graphs above show the characteristics for r70 leds of this product.
nichia sts-da1-2675a 16 forward current characteristics / temperature characteristics ? no. NSBWL066A sts-da7-4320 taxy 0.33 0.34 0.35 0.36 0.37 0.32 0.33 0.34 0.35 0.36 -4 0c 25c 100c 0 c x ifxy 0.33 0.34 0.35 0.36 0.37 0.32 0.33 0.34 0.35 0.36 20ma 320ma 900ma x y y 320ma i fp = ??-? ambient temperature vs chromaticity coordinate -? forward current vs chromaticity coordinate t a =25c * ??? all characteristics shown are for reference only and are not guaranteed. * ??? r8000 ???? the graphs above show the characteristics for r8000 leds of this product.
nichia sts-da1-2675a 17 reliability (1) tests and results te s t reference standard test conditions te s t duration failure criteria # units failed/tested temperature cycle jeita ed-4701 100 105 -40c(30min)~25c(5min)~ 100c(30min)~25c(5min) 100cycles #1 0/10 high temperature storage jeita ed-4701 200 201 t a =100c 1000hours #1 0/10 temperature humidity storage jeita ed-4701 100 103 t a =60c, rh=90% 1000hours #1 0/10 low temperature storage jeita ed-4701 200 202 t a =-40c 1000hours #1 0/10 high temperature operating life t c =85c, i f =600ma 1000hours #1 0/10 electrostatic discharges jeita ed-4701 300 304 hbm, 2kv, 1.5k ? , 100pf, 3pulses, alternately positive or negative #1 0/10 notes: measurements are performed after allowi ng the leds to return to room temperature. (2) failure criteria criteria # items conditions failure criteria forward voltage(v f ) i f =320ma >initial value1.1 #1 luminous flux( v ) i f =320ma nichia sts-da1-2675a 18 cautions (1) storage conditions temperature humidity time before opening aluminum bag 30c 90%rh within 1 year from delivery date storage after opening aluminum bag 30c 70%rh 168hours after opening the moisture-proof aluminum bag, the products should go through the soldering process within the range of the conditions stated above. unused remaining leds should be stored with silica gel desiccants in a hermetically sealed container, preferab ly the original moisture-proof bags for storage. although the leads or electrode pads (anode and cathode) of the product are plated with gold, prolonged exposure to a corrosive environment might caus e the gold plated the leads or electrode pads to tarnish. if unused leds remain, they must be st ored in a hermetically sealed container. nichia recommends using the origin al moisture-proof bag for storage. do not use sulfur-containing materials in commercial products. some materials, such as seals and adhesives, may contain sulfur . the contaminated plating of leds might cause an open circ uit. silicone rubber is recommen ded as a material for seals. bear in mind, the use of silicones may lead to silicone contamination of electrical contacts inside the products, caused by low molecular weight volatile siloxane. to prevent water condensation, please avoid large temperat ure and humidity fluctuations for the storage conditions. do not store the leds in a dusty environment. do not expose the leds to direct sunlight and/or an environment where the temperature is higher than normal room temperature. (2) directions for use when designing a circuit, the curre nt through each led must not exceed the absolute maximum rating. operating at a constant current per led is recommended. in case of operating at a constant voltage, circuit b is recommended . if the leds are operated with constant voltage using circui t a, the current through the leds may vary due to the variation in forward voltage ch aracteristics of the leds. (a) ... (b) ... this product should be operated using forward curre nt. ensure that the product is not subjected to either forward or reverse voltage while it is not in use. in particular, subjecting it to continuous reverse voltage may cause migration, which may cause damage to the led die. when used in displays that are not used for a long time, the main power supply should be switched off for safety. pulse width modulation (pwm) is recommended for dimm ing leds as color point changes with drive current. it is recommended to operate the leds at a current greater th an 10% of the sorting current to stabilize the led characteristic s. ensure that excessive voltages such as li ghtning surges are not applied to the leds. for outdoor use, necessary measures should be take n to prevent water, moisture and salt air damage. (3) handling precautions do not handle the leds with bare hands as it will contaminat e the led surface and may affect the optical characteristics: it might cause the led to be deformed and/or the wi re to break, which will cause the led not to illuminate. when handling the product with tweezers, be ca reful not to apply excess ive force to the resin. otherwise, the resin can be cut, ch ipped, delaminate or deform ed, causing wire-bond breaks and catastrophic failures. dropping the product may cause damage. do not stack assembled the products. fail ure to comply can cause the resin portion of the product to be cut, chipped, delaminated and/or deformed. it may cause wi re to break, leading to catastrophic failures.
nichia sts-da1-2675a 19 (4) design consideration excessive forces on this product ca n cause the ceramic package to crack. it is recommended to use a holder when fixing this product to a chassis. it is recommended to use a thermal film or thermal grease between the product and a chassis for increased heat dissipation. (5) electrostatic discharge (esd) the products are sensitive to static electricity or surge voltage. esd can damage a die and its reliability. when handling the products, the following measures against electrostatic discharge are strongly recommended: eliminating the charge grounded wrist strap, esd footwear, clothes, and floors grounded workstation equipment and tools esd table/shelf mat made of conductive materials ensure that tools (e.g. soldering irons), jigs and mach ines that are being used are properly grounded and that proper grounding techniques are used in wo rk areas. for devices/equipment that mount the leds, protection against surge voltages should also be used. if tools or equipment contain insulating materials such as glass or plastic, the following measures against electros tatic discharge are strongly recommended: dissipating static charge with conductive materials preventing charge generation with moisture neutralizing the charge with ionizers (6) thermal management proper thermal management is an impo rtant when designing products with le ds. led die temperature is affected by led module thermal resistance and led spacing. please design products in a way that the led die temperature does not exceed the maximum junction temperature (t j ). the dice temperature of the products should be calculated, using the case temperature (t c ) of the product incorporated into the end-product, by the following equation. t j =t c +r jc ? w *t j =led junction temperature: c t c =case temperature: c r jc =thermal resistance from junction to t c measuring point: c/w w=input power(i f v f ): w tc point (7) cleaning the leds should not be cleaned with water, benzine, and/or thinner. if required, isopropyl alcohol (ipa) should be used. ot her solvents may cause premature failure to the leds due to the damage to the resin portion. the effects of such solvents should be verified prior to use. in addition, the use of cfcs such as freon is heavily regulated. when dust and/or dirt adheres to the leds, soak a cloth with is opropyl alcohol (ipa), then sque eze it before wiping the leds. ultrasonic cleaning is not recommended sinc e it may have adverse effects on the leds depending on the ultrasonic power and how led is assembled. if ultrasonic cleaning must be used, the customer is advise d to make sure the leds will not be damaged prior to cleaning.
nichia sts-da1-2675a 20 (8) eye safety in 2006, the international electrical commission (iec) published iec 62471:2006 photobiological safety of lamps and lamp systems, which added leds in its scope. on the other hand, the iec 60825-1:2007 laser safety standard removed leds from its scope. however, please be advised that some countries and regions have adopted standards based on the iec laser safety standard iec 60825- 1:20112001, which still includes leds in its scope. most of nichia's leds can be classified as belo nging into either the exempt group or risk group 1. high-power leds, that emit ligh t containing blue wavelengths, may be classified as risk group 2. please proceed with caution when viewing directly any leds driven at high current, or viewing leds with optical instruments which may greatly increase the damages to your eyes. viewing a flashing light may cause eye discomfort. when incorporating the led into your product, please be careful to avoid adverse effects on the human body caused by light stimulation. (9) others the leds described in this brochure are intended to be used for ordinary electronic equipmen t (such as office equipment, communications equipment, measurement instruments and household appliances). consult nichia's sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the leds may directly jeopardize life or health (such as for airplanes, aerospace, submersibl e repeaters, nuclear reactor co ntrol system, automobiles, traffic control equipment, life support systems and safety devices). the customer shall not reverse engineer by disassembling or analysis of the leds without having prior written consent from nichia. when defective leds are found, the customer sh all inform nichia directly before disassembling or analysis. the specifications and appearance of th is product may change without notice; nichia does not guarantee the contents of this specification. both the customer and nichia will agree on the official specifications of supplied products before the volume production of a program begins.
|
